Filter
Bridge between AQS-LoRa and Dry Contacts
The Dry Contact Controller connects wireless Aqua-Scope devices that are both controlled and controlling with the world of wired controls. With this device, it is possible to control an Aqua-Scope motor servo directly through a switch input. This switch input can be directly connected to an actuator of your alarm system or smart home system (Shelly, Z-Wave, Smartthings, Bosch, Homematic, ...). The Dry Contact Controller will transmit the information at the switch input wirelessly as a control signal to the motor. Conversely, a normal magnetic shut-off valve or a similar actuator can be controlled by the Aqua-Scope sensor/monitor using the Dry Contact Controller. The device requires a power supply, which can be provided through a regular 6...16 V AC connection, a USB-C power supply, or a 3 V battery. All connections, including switch inputs, switch outputs, and power supply, are connected via screw terminals. The button on the device can be used to test the quality of the wireless connection to or from the Aqua-Scope device.

Delivery time 1-3 days

Product number DRYLWE02

€49.00*

ER26500 Bobbin Cell Battery
This lithium battery (Li-SOCl2) provides approximately 9000 mAh at a cell voltage of 3.6 V. The manufacturer EVE is one of the leading providers of lithium cells for professional applications.

Delivery time 1-3 days

Product number ER26500

€10.00*

Flood / Humidity / Temperature Sensor for AQS-LoRa
The Flood Sensor detects the presence of water on its sensor pins and sends an alarm message wirelessly when triggered. In addition, the device will regularly report the ambient temperature and humidity and send an alarm when the readings exceed thresholds that can be set for both humidity and temperature. The device itself is designed to sit on the floor, where 3 brass telescopic pins can detect water on both hard floors (tiles) and soft carpets. The unit comes with a mounting bracket. It can be screwed or taped to the wall or floor. When the main sensor is in the bracket, a super-flat sensor pad con-nected by wire to the bracket is used to detect water. When an alarm is active, the unit emits a sound and a red LED flash. The unit is powered by an internal CR123 battery that lasts approximately 10 years in normal operation. The device can be directly connected to an Aqua-Scope leak monitor and sends its information directly to the Aqua-Scope system.

Delivery time 1-3 days

Product number FLOLWE02

€49.00*

Floodsensor-Cable
The wired flood sensor can be connected to all Aqua-Scope actuators, pressure sensors, and Aqua-Scope monitors through the respective 3.5 mm audio jack. At the end of the 138 cm long cable, there is a sensor head that detects water through two exposed electrodes and triggers an alarm accordingly. The sensor head can be optionally mounted on the wall or directly on the floor. It will function equally well on hard floors (tiles) as on carpeted floors and even on high-pile carpets. In this case, two spacers on the right and left can be removed, allowing the electrodes to securely reach the floor of the carpet and detect any form of water. The sensor is part of the scope of delivery on the retrofit-motors KFRLWE01, BVSLWE01, BVSLWE02, the Aqua-Scope Leckage Monitors AQSLWE02, AQSWIE02, and the water pressure sensors PRELWE02, PREWIE02.

Delivery time 1-3 days

Product number ALIXXX01

€13.00*

Retofit Motor for Ball Valves for AQS-LoRa
This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device can be directly connected to an Aqua-Scope leak monitor and sends its information directly to the Aqua-Scope system. For controlling the device using LoRaWAN please use SKU BVSLWE01. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSLWE02

€199.00*