Products

Welcome to the Aqua-Scope Shop!

Stop Water Leaks - DIY in 10 Minutes !

Aqua-Scopes Water Leakage Protection is on duty 24/7 to protect your home from water leakage. A Highly-sensitive pressure sensor plus a network of distributed sensors placed on strategic points in the home permanently analyses the situation in your water pipes. They will detect leaks well before they cause any damage. If something happens, the Valve Servos will automatically shut off the water. But the best, all this can be installed in a few minutes without any pipes being cut.

TIP

'Offline' Leckage Protection System - 1x Gate Valve (Lora) + 3x Flood Sensors (Lora)

The offline leakage protection system 'KFRFLO' detects water leaks using multiple water sensors distributed throughout the house and shuts off the water supply in the event of a leak. The unique feature of this system is that it does not require an app, internet, or Wi-Fi The retrofit motor is installed in place of the handwheel on the main shut-off valve. The product bundle includes three battery-operated water sensors that are paired with the motor and distributed around the house. Communication between the sensors and the motor uses the highly reliable, standardized LoRa wireless technology, specifically designed for such applications. No additional equipment like a gateway is needed. All sensors communicate directly with the motor in case of an alarm, making the system installation very straightforward. In the event of an alarm, the affected sensor emits a loud audible signal and flashes red. The motor shuts off the water, also emitting an audible signal and flashing red. The alarm can be cleared, and the water turned back on by pressing the button on the motor. The bundle consists of a KFRLWE01 retrofittable motor for Gate-Valves and three Water Sensors FLOLWE02.

Delivery time 1-3 days

Product number KFRFLO01

€426.00*

Aqua-Scope Leckage Protection & Water Consumption Monitor (Wifi)

The Aqua-Scope water monitor detects water consumption and leaks by analyzing pressure waves in the water supply. It continuously records the temperature, water consumption, and water pressure. When leaks are detected or when pressure or temperature thresholds are exceeded or not reached, the user is alerted wirelessly. An additional wired flood sensor can be connected directly to the device, triggering an alarm when water is detected. The device consists of two parts: Main Unit (Monitor): Detects water consumption and leaks by analyzing pressure waves; Records temperature, water consumption, and water pressure continuously; Wireless alerts for detected leaks or when pressure or temperature thresholds are exceeded or not reached; Option to connect an additional wired flood sensor directly to the device. External Sensor Head: Connected to the water pipe, installed somewhere in the building at a 1/8-inch inspection opening, or with a provided T-piece under any sink at the angle valve. For water consumption metering an installed Pressure Reducing Valve is required. Thanks to the excellent sound characteristics of water, a single sensor somewhere in the house is sufficient to detect water consumption and leaks throughout the entire building. The device communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or through MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The device can be powered either by an external power supply with a USB-C adapter or by an optional internal ER26500 battery (Bobbin Cell C). Both the sensor head (IP67) and the main housing (IP65) are waterproof, allowing them to be used outdoors or in particularly damp and/or dirty environments.

Delivery time 1-3 days

Product number AQXWIE02

€349.00*

Aqua-Scope Leckage Protection Monitor (Wifi)

The Aqua-Scope water monitor detects leaks by analyzing pressure waves in the water supply. It continuously records the temperature, and water pressure. When leaks are detected or when pressure or temperature thresholds are exceeded or not reached, the user is alerted wirelessly. An additional wired flood sensor can be connected directly to the device, triggering an alarm when water is detected. The device consists of two parts: Main Unit (Monitor): Detects water consumption and leaks by analyzing pressure waves; Records temperature, water consumption, and water pressure continuously; Wireless alerts for detected leaks or when pressure or temperature thresholds are exceeded or not reached; Option to connect an additional wired flood sensor directly to the device. External Sensor Head: Connected to the water pipe, installed somewhere in the building at a 1/8-inch inspection opening, or with a provided T-piece under any sink at the angle valve. Thanks to the excellent sound characteristics of water, a single sensor somewhere in the house is sufficient to detect water consumption and leaks throughout the entire building. The device communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or through MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The device can be powered either by an external power supply with a USB-C adapter or by an optional internal ER26500 battery (Bobbin Cell C). Both the sensor head (IP67) and the main housing (IP65) are waterproof, allowing them to be used outdoors or in particularly damp and/or dirty environments.

Delivery time 1-3 days

Product number AQSWIE02

€199.00*

Bridge between AQS-LoRa and Dry Contacts

The Dry Contact Controller connects wireless Aqua-Scope devices that are both controlled and controlling with the world of wired controls. With this device, it is possible to control an Aqua-Scope motor servo directly through a switch input. This switch input can be directly connected to an actuator of your alarm system or smart home system (Shelly, Z-Wave, Smartthings, Bosch, Homematic, ...). The Dry Contact Controller will transmit the information at the switch input wirelessly as a control signal to the motor. Conversely, a normal magnetic shut-off valve or a similar actuator can be controlled by the Aqua-Scope sensor/monitor using the Dry Contact Controller. The device requires a power supply, which can be provided through a regular 6...16 V AC connection, a USB-C power supply, or a 3 V battery. All connections, including switch inputs, switch outputs, and power supply, are connected via screw terminals. The button on the device can be used to test the quality of the wireless connection to or from the Aqua-Scope device.

Delivery time 1-3 days

Product number DRYLWE02

€49.00*

ER26500 Bobbin Cell Battery

This lithium battery (Li-SOCl2) provides approximately 9000 mAh at a cell voltage of 3.6 V. The manufacturer EVE is one of the leading providers of lithium cells for professional applications.

Delivery time 1-3 days

Product number ER26500

€10.00*

Flood, Humidity & Temperature Sensor (LoRaWAN)

The Flood Sensor detects the presence of water on its sensor pins and sends an alarm message wirelessly when triggered. In addition, the device will regularly report the ambient temperature and humidity and send an alarm when the readings exceed thresholds that can be set for both humidity and temperature. The device itself is designed to sit on the floor, where 3 brass telescopic pins can detect water on both hard floors (tiles) and soft carpets. The unit comes with a mounting bracket. It can be screwed or taped to the wall or floor. When the main sensor is in the bracket, a super-flat sensor pad con-nected by wire to the bracket is used to detect water. When an alarm is active, the unit emits a sound and a red LED flash. The unit is powered by an internal CR123 battery that lasts approximately 10 years in normal operation. The device is controlled via LoRaWAN commands and operates as a LoRaWAN Class A device. The use of the device requires LoRaWAN network coverage. Otherwise, you need to install and operate your own LoRaWAN gateway.If you like to operate the device directy from a Aqua-Scope Monitor AQSWIE02, please use FLOLWE02.

Delivery time 1-3 days

Product number FLOLWE01

€49.00*

Flood, Humidity & Temperature Sensor for AQS (LoRa)

The Flood Sensor detects the presence of water on its sensor pins and sends an alarm message wirelessly when triggered. In addition, the device will regularly report the ambient temperature and humidity and send an alarm when the readings exceed thresholds that can be set for both humidity and temperature. The device itself is designed to sit on the floor, where 3 brass telescopic pins can detect water on both hard floors (tiles) and soft carpets. The unit comes with a mounting bracket. It can be screwed or taped to the wall or floor. When the main sensor is in the bracket, a super-flat sensor pad con-nected by wire to the bracket is used to detect water. When an alarm is active, the unit emits a sound and a red LED flash. The unit is powered by an internal CR123 battery that lasts approximately 10 years in normal operation. The device can be directly connected to an Aqua-Scope leak monitor and sends its information directly to the Aqua-Scope system.

Delivery time 1-3 days

Product number FLOLWE02

€49.00*

Floodsensor-Cable (Binary)

The wired flood sensor can be connected to all Aqua-Scope actuators, pressure sensors, and Aqua-Scope monitors through the respective 3.5 mm audio jack. At the end of the 138 cm long cable, there is a sensor head that detects water through two exposed electrodes and triggers an alarm accordingly. The sensor head can be optionally mounted on the wall or directly on the floor. It will function equally well on hard floors (tiles) as on carpeted floors and even on high-pile carpets. In this case, two spacers on the right and left can be removed, allowing the electrodes to securely reach the floor of the carpet and detect any form of water. The sensor is part of the scope of delivery on the retrofit-motors KFRLWE01, BVSLWE01, BVSLWE02, the Aqua-Scope Leckage Monitors AQSLWE02, AQSWIE02, and the water pressure sensors PRELWE02, PREWIE02.

Delivery time 1-3 days

Product number ALIXXX01

€13.00*

Leakage Protection Kit 'PLUS' for Ball Valves (Wifi)

The Aqua-Scope Leak Protection System AQSKFR02 monitors the water pipes of a building and shuts off the water in case of leaks. Thanks to the wireless control, the user can also turn the water off and on manually or set it on a programmable timer. The system consists of the Aqua-Scope Monitor as the main device with its water pressure sensor, two further wireless flood sensors, two wired flood sensors to be connected to the actuator and the main device and the actuator for a ball valve to shut off the water. The monitor monitors all water pipes from the main water meter. The water pressure and temperature are regularly measured and transmitted wirelessly. An additional wired sensor can be connected to both the monitor and the actuator. If such a sensor detects water leakage, the user is alerted, and depending on the user configuration, the water is immediately shut off. The system communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or via MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The communication between devices is through a robust LoRa connection, allowing the main device, for example, to be installed on the first or second floor while the actuator can be in the basement or even outside the house. This is a bundle consisting of the following devices: 1* AQXWIE02, 1 * BVSLWE02, 2*FLOLWE02, 2 *ALIXXX01 as part of the former devices. Please note that this is a soft bundle. You will receive individual packaging for the four main products. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number AQSBVS02

€649.00*

Leakage Protection Kit 'PLUS' for Gate Valves (Wifi)

The Aqua-Scope Leak Protection System AQSKFR02 monitors the water pipes of a building and shuts off the water in case of leaks. Thanks to the wireless control, the user can also turn the water off and on manually or set it on a programmable timer. The system consists of the Aqua-Scope Monitor as the main device with its water pressure sensor, two further wireless flood sensors, two wired flood sensors to be connected to the actuator and the main device and the actuator for a KFR angle seat valve to shut off the water. The monitor monitors all water pipes from the main water meter. The water pressure and temperature are regularly measured and transmitted wirelessly. An additional wired sensor can be connected to both the monitor and the actuator. If such a sensor detects water leakage, the user is alerted, and depending on the user configuration, the water is immediately shut off. The system communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or via MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The communication between devices is through a robust LoRa connection, allowing the main device, for example, to be installed on the first or second floor while the actuator can be in the basement or even outside the house. This is a bundle consisting of the following devices: 1* AQXWIE02, 1 * KFRLWE01, 2*FLOLWE02, 2 *ALIXXX01 as part of the former devices. Please note that this is a soft bundle. You will receive individual packaging for the four main products.

Delivery time 1-3 days

Product number AQSKFR02

€698.00*

Leckage Protection Kit 'Basic' for Ball Valves

The Aqua-Scope Leak Protection System AQSKFR01 monitors the water pipes of a building and shuts off the water in case of leaks. Thanks to the wireless control, the user can also turn the water off and on manually or set it on a programmable timer. The system consists of the Aqua-Scope Monitor as the main device with its water pressure sensor and the actuator for a ball valve to shut off the water. The monitor monitors all water pipes from the main water meter. The water pressure and temperature are regularly measured and transmitted wirelessly. An additional wired sensor can be connected to both the monitor and the actuator. If such a sensor detects water leakage, the user is alerted, and depending on the user configuration, the water is immediately shut off. The system communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or via MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The communication between devices is through a robust LoRa connection, allowing the main device, for example, to be installed on the first or second floor while the actuator can be in the basement or even outside the house. This is a bundle consisting of the following devices: 1* AQSWIE02, 1 * BVSLWE02, 2 *ALIXXX01 as part of the former devices. Please note that this is a soft bundle. You will receive individual packaging for the two main products. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number AQSBVS01

€399.00*

Leckage Protection Kit 'Basic' for Gate Valves

The Aqua-Scope Leak Protection System AQSKFR01 monitors the water pipes of a building and shuts off the water in case of leaks. Thanks to the wireless control, the user can also turn the water off and on manually or set it on a programmable timer. The system consists of the Aqua-Scope Monitor as the main device with its water pressure sensor and the actuator for a KFR angle seat valve to shut off the water. The monitor monitors all water pipes from the main water meter. The water pressure and temperature are regularly measured and transmitted wirelessly. An additional wired sensor can be connected to both the monitor and the actuator. If such a sensor detects water leakage, the user is alerted, and depending on the user configuration, the water is immediately shut off. The system communicates via WLAN, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or via MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The communication between devices is through a robust LoRa connection, allowing the main device, for example, to be installed on the first or second floor while the actuator can be in the basement or even outside the house. This is a bundle consisting of the following devices: 1* AQSWIE02, 1 * KFRLWE01, 2 *ALIXXX01 as part of the former devices. Please note that this is a soft bundle. You will receive individual packaging for the two main products.

Delivery time 1-3 days

Product number AQSKFR01

€399.00*

TIP

LoRain - complete kit

This rain sensor measures the amount of rain at its location in milliliters using a tipping bucket mechanism and transmits the quantity within a 15-minute interval with an accuracy of 0.5 mm of water column, along with the temperature. In the case of heavy rain exceeding 15 l/h, a heavy rain alarm is triggered promptly. Both the heavy rain threshold and the measurement interval are configurable. The device is entirely open-source, and both hardware and firmware can be downloaded from https://github.com/aqua-scope/lorain. The product is delivered as a kit with a pre-assembled circuit board and casing. Only the connections to the battery compartment, the antenna, and the reed sensor for rain detection need to be soldered. The device is controlled via LoRaWAN commands and operates as a LoRaWAN Class A device. The use of the device requires LoRaWAN network coverage. Otherwise, you need to install and operate your own LoRaWAN gateway. The sensor is powered by two AAA batteries. The provided VARTA batteries allow for an approximate runtime of about 2 years. A low battery level is reported wirelessly, allowing for battery replacement before the device shuts down.

Delivery time 1-3 days

Product number RANLWE01_E1

€55.00*

TIP

LoRain - Rain Gauge (LoRaWAN)

This rain gauge measures the amount of rain at its location in milliliters using a tipping bucket mechanism and transmits the quantity within a 15-minute interval with an accuracy of 0.5 mm of water column, along with the temperature. In the case of heavy rain exceeding 15 l/h, a heavy rain alarm is triggered promptly. Both the heavy rain threshold and the measurement interval are configurable. The device is entirely open-source, and both hardware and firmware can be downloaded from https://github.com/aqua-scope/lorain. The device is controlled via LoRaWAN commands and operates as a LoRaWAN Class A device. The use of the device requires LoRaWAN network coverage. Otherwise, you need to install and operate your own LoRaWAN gateway. The device is powered by two AAA batteries. The provided VARTA batteries allow for an approximate runtime of about 2 years. A low battery level is reported wirelessly, allowing for battery replacement before the device shuts down.

Delivery time 1-3 days

Product number RANLWE01

€69.00*

LoRain Housing

Lorain base housing is made of plastic in unobtrusive dark gray. The housing consists of the base part with a small spirit level to allow a clean installation on a flat place. Also built into the base housing is the waterproof bottom housing for the electronics and the water rocker for measuring the water. A cover with the water funnel is placed over the base housing. The electronics base housing holds the Lorain circuit board and two AAA batteries.

Delivery time 1-3 days

Product number RANLWE01-E2

€26.00*

TIP

Rain Gauge (Wifi - MQTT)

This rain gauge measures the amount of rain at its location in milliliters using a tipping bucket mechanism and transmits the quantity within a 15-minute interval with an accuracy of 0.5 mm of water column, along with the temperature. In the case of heavy rain exceeding 15 l/h, a heavy rain alarm is triggered promptly. Both the heavy rain threshold and the measurement interval are configurable. The device is entirely open-source, and both hardware and firmware can be downloaded from https://github.com/aqua-scope/lorain. The device communicates via WIFI, either to the Aqua-Scope Cloud and thus to an app on your mobile phone or PC, or through MQTT to a server of your choice, or as a JSON object to a Smart Home Gateway. The device is powered by two AAA batteries. The provided VARTA batteries allow for an approximate runtime of about 2 years. A low battery level is reported wirelessly, allowing for battery replacement before the device shuts down.

Delivery time 1-3 days

Product number RANWIE01

€59.00*

Retrofit Motor for Ball Valves - direct connection to AQS (LoRa)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device can be directly connected to an Aqua-Scope leak monitor and sends its information directly to the Aqua-Scope system. For controlling the device using LoRaWAN please use SKU BVSLWE01. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSLWE02

€199.00*

Retrofit Motor for Ball Valves (dry input wire controlled)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device is controlled either through the local button or via a switch input of the existing smart home system or your alarm system. This switch input is connected to an actuator of your alarm system or smart home system (Shelly, Z-Wave, Smartthings, Bosch, Homematic, ...) for control. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSDRY01

€139.00*

TIP

Retrofit Motor for Ball Valves (remotely switched by dry contact controller)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off.The device is controlled either through the local button or a switch input on the 'Dry Contact Controller.' The connection between the Dry Contact Controller and the actual motor is established through an encrypted LoRa wireless connection. This robust wireless technology allows for seamless motor control through multiple walls or in the garden. This product is a combination of BVSLWE02 and DRYLWE02 but is delivered in one single box. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSDRY02

€219.00*

Retrofit Motor for Gate Valves (dry input wire controlled)

The motor drive for angle seat valves (KFR valves) allows for the retrofitting of existing and already installed shut-off valves into remotely controlled intelligent devices without interrupting the water supply or cutting into the water pipe. The motor is powered by a 12V power supply and is completely water and dirt-resistant up to the power supply. Various adapter rings and a sophisticated connection system enable the use of the motor on all modern angle seat valves from DN15 to DN32. Thanks to an additional water sensor that is directly connected to the device, the motor can be used for leak protection without further configuration. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device is controlled either through the local button or via a switch input of the existing smart home system or your alarm system. This switch input is connected to an actuator of your alarm system or smart home system (Shelly, Z-Wave, Smartthings, Bosch, Homematic, ...) for control.

Delivery time 1-3 days

Product number KFRDRY01

€249.00*

Retrofit Motor for Gate Valves (remotely switched by dry contact controller)

The motor drive for angle seat valves (KFR valves) allows for the retrofitting of existing and already installed shut-off valves into remotely controlled intelligent devices without interrupting the water supply or cutting into the water pipe. The motor is powered by a 12V power supply and is completely water and dirt-resistant up to the power supply. Various adapter rings and a sophisticated connection system enable the use of the motor on all modern angle seat valves from DN15 to DN32. Thanks to an additional water sensor that is directly connected to the device, the motor can be used for leak protection without further configuration. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off.The device is controlled either through the local button or a switch input on the 'Dry Contact Controller.' The connection between the Dry Contact Controller and the actual motor is established through an encrypted LoRa wireless connection. This robust wireless technology allows for seamless motor control through multiple walls or in the garden. This product is a combination of KFRLWE01 and DRYLWE02 but is delivered in one single box.

Delivery time 1-3 days

Product number KFRDRY02

€279.00*

Retrofit-Motor for Ball Valves (LoRaWAN)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device is controlled via local buttons and remotely using LoRaWAN commands and it operates as a LoRaWAN Class C device. The use of the device requires LoRaWAN network coverage. Otherwise, you need to install and operate your own LoRaWAN gateway. For direct coupling to an Aqua-Scope Monitor AQSWIE02 please use BVSLWE02. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSLWE01

€199.00*

Retrofit-Motor for Ball Valves (Z-Wave - alarm.com)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device is controlled either through the local button or via a Z-Wave network and is optimized and certified for use with alarm.com. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSZWE02

€199.00*

Retrofit-Motor for Ball Valves (Z-Wave)

This motor converts existing and installed ball valves into intelligent water control devices. Thanks to the innovative clamp mechanism, it can be installed on shut-off valves with a pipe diameter between 0.5 and 1.5 inches within minutes, without the need for additional tools, and can be removed just as easily. A patented coupling mechanism allows for torques of up to 8 Nm, enabling it to function even with rusty and old valves. The servo motor is waterproof and can be used in damp, dirty, and outdoor environments. In the open position, the motor automatically performs valve training once a week (closing/opening by 1/8 turn to remove dirt and scale). The device is also capable of measuring the rotation angle and detecting the end positions of the lever. It approaches the end positions slowly to avoid friction and unnecessary mechanical stress. It is powered by an external 12V power supply through a waterproof coupling. A wired leakage sensor can be directly connected to the device. If this sensor detects water, the valve is shut off. The device is controlled either through the local button or via a Z-Wave network. Please refer to the Installation Requirements for the retofittable motor.

Delivery time 1-3 days

Product number BVSZWE01

€199.00*

Sign up for our newsletter